{"id":7720,"date":"2017-01-04T10:11:35","date_gmt":"2017-01-04T18:11:35","guid":{"rendered":"http:\/\/museumtrade.org\/Base1\/?p=7720"},"modified":"2019-05-20T09:29:16","modified_gmt":"2019-05-20T16:29:16","slug":"adhesion-fundamentals-tapes-seals-etc","status":"publish","type":"post","link":"https:\/\/museumtrade.org\/Base1\/adhesion-fundamentals-tapes-seals-etc\/","title":{"rendered":"Adhesion Fundamentals – Tapes, Seals, Etc."},"content":{"rendered":"
\n

Did you know that packing tape requires pressure to fully adhere? It’s a pressure sensitu=ive tape and so are a lot of the products we use in the Museum Trade. I found a nice succinct description of what is happening with the adhesive and how to make the most of it.<\/p>\n

Different adhesives are used for different purposes. Selecting the proper adhesive requires the consideration of several important factors; adhesion values, surface contact, substrates, environmental conditions, and performance requirements. The purpose here is to cover some of the principles of adhesion.<\/p>\n

Surface contact is fundamental to adhesive performance.<\/p>\n

To maximize adhesive contact on a surface:<\/p>\n

\u2022 Substrate must be unified, dry, and free of contaminates.<\/p>\n

\u2022 Firm pressure must be applied to increase the flow and contact of the adhesive with the substrate.<\/p>\n

\u2022 Time and temperature will increase the surface contact and adhesion values.<\/p>\n

INITIAL CONTACT (Minimal Contact)<\/h3>\n

(Adhesive\u00a0surface above,\u00a0green.\u00a0Bonding\u00a0surface below, blue)<\/em><\/p>\n

\"\"<\/a><\/p>\n

AFTER RUBDOWN\u00a0(More Contact)<\/h3>\n

\"\"<\/a><\/p>\n

AFTER DWELL TIME (Excellent Contact)<\/h3>\n

\"\"<\/a><\/p>\n

Surface Energy<\/h3>\n

Adhesion is the molecular force of attraction between unlike materials. The strength of attraction is determined by the surface energy of the material. The higher the surface energy, the greater the molecular attraction. The lower the surface energy, the weaker the attractive forces.<\/p>\n

Greater molecular attraction results in increased contact between an adhesive and substrate. In other words, on a high surface energy material, the adhesive can flow (or “wet-out”) to assure a stronger bond.<\/p>\n

Consider an automobile that has not been waxed for a long time. When water contacts the surface it spreads in large puddles. The unwaxed car surface exhibits high surface energy – the molecular attraction allows the water to flow.<\/p>\n

In comparison, water beads up into small spheres on a freshly waxed car. It is an example of low surface energy – the liquid (or adhesive) does not flow out.<\/p>\n

Substrates<\/h3>\n

Surface roughness or smoothness, coated or uncoated, flexibility, and part size must all be considered. Foam tapes can achieve more surface contact than thin tapes on rougher surfaces. If the surface is coated, the coating’s surface energy must be considered. Smaller, more flexible parts can be bonded with thinner products such as double coated adhesives. Larger, more rigid parts require thicker products such as foam tapes (HATS adhesive).<\/p>\n

Environmental Conditions<\/h3>\n

The types of exposure the bonds will be required to resist must be taken into consideration. These include temperature extremes, sunlight (UV), water, oils or solvents.<\/p>\n

Performance Requirements<\/h3>\n

Consider what forms of stresses will be present: tensile, shear, cleavage, or peel.<\/p>\n

Tensile<\/em>:<\/span>\u00a0Forces perpendicular to the bond plane. Stress is distributed over the entire bond area. The entire adhesive contributes to the bond strength.<\/p>\n

Shear<\/em>:<\/span>\u00a0Forces parallel to the joint plane. As with tensile, stress is distributed over the entire bond area.<\/p>\n

Cleavage<\/em>:<\/span>\u00a0Forces concentrated at the edge of the bond. Not all of the bond area is contributing to the overall strength at one time.<\/p>\n

Peel<\/em>:<\/span>\u00a0Forces confined to the edge of the bond. At least one surface is flexible. Even less adhesive contributes to the bond strength than in cleavage.<\/p>\n<\/div>\n

Tensile:<\/strong><\/p>\n

\"\"<\/a><\/strong><\/p>\n

Sheer:<\/strong><\/p>\n

\"\"<\/a><\/strong><\/p>\n

Cleavage:<\/strong><\/p>\n

\"\"<\/a><\/strong><\/p>\n

Peel:<\/strong><\/p>\n

\"\"<\/a><\/p>\n

 <\/p>\n

A big thanks to CleanSeal<\/a> for this break down.<\/p>\n

<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n","protected":false},"excerpt":{"rendered":"

Did you know that packing tape requires pressure to fully adhere? It’s a pressure sensitu=ive tape and so are a lot of the products we use in the Museum Trade. I found a nice succinct description of what is happening with the adhesive and how to make the most of it. Different adhesives are used […]<\/p>\n","protected":false},"author":78,"featured_media":7726,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[284],"tags":[558,557,560,559,556],"jetpack_featured_media_url":"https:\/\/museumtrade.org\/Base1\/wp-content\/uploads\/2017\/01\/tensilestress.png","_links":{"self":[{"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/posts\/7720"}],"collection":[{"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/users\/78"}],"replies":[{"embeddable":true,"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/comments?post=7720"}],"version-history":[{"count":1,"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/posts\/7720\/revisions"}],"predecessor-version":[{"id":9365,"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/posts\/7720\/revisions\/9365"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/media\/7726"}],"wp:attachment":[{"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/media?parent=7720"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/categories?post=7720"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/museumtrade.org\/Base1\/wp-json\/wp\/v2\/tags?post=7720"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}